发博工控

22550 TOOL_CHANGE_MODE ：T功能执行后，是否立即装载新刀。

0：立即执行。

准备刀和换刀在一个NCK程序块里。例如，执行T后，激活新的刀具偏差（参阅20270: CUTTING_EDGE_DEFAULT）

1：执行T功能后，准备装载新刀。这个功能主要用于带刀库的铣床，主要是为了换刀是不影响加工。

22560 TOOL_CHANGE_M_CODE

从主轴上移去旧刀并装载新刀。换刀需要执行M06，同DIN66025一致。

20121:

The next tool is preselected with MD 20121: TOOL_PRESEL_RESET_VALUE whose assigned tool length compensation values must be taken into account on RESET and power up according to MD 20110: RESET_MODE_MASK are to be taken into account.

20270: 未编程前刀具切削沿的初始位置

= 1 M06之后没有自动选择刀沿号

=  0 M06之后自动选择刀沿号

= –1 M06之后保留旧刀刀沿号并为新刀选择刀沿

28085: 指定TO单元到通道

用来定义为适当通道定义哪个TO存储器

18100: 每个TOA程序块刀具偏移

由NCK管理的所有刀具的刀沿的最大数量由该参数设定

18105 D号的最大值

所允许定义的最大D号。

18106 每个刀具号D号的最大数量



$TC_DPCE[t,d].

18102: MM_TYPE_OF_CUTTING_EDGE. D编号类型类型

the ‘18102’ function is active, only one D offset can be defined in the TO unit.

TOOL_CHANGE_ERROR_MODE Bit 0 = 1).

If a program error has occurred, the line with the error cannot be corrected (Txx); only the line at which the program stopped and which generated the alarm can be edited

11346 手轮缺省路径或速度

= 1 通过该参数设定手轮距离。在DRF手轮移动的过程中，可以仅仅通过指定增量一半的距离来移动轴。

20360 定义刀具参数

通过设定位9等于1，来定义移动轴中作为直径偏置的DRF偏置。当取消轴的DRF偏置，则现存的刀具偏置同时取消。

18102 D编号类型类型

= 0 默认设置

_ Value = 1 = flat D number structure with absolute direct D programming

Cutting edges can be deleted individually via PI command or NC programming command.

Cutting edges with a specific number can also be created selectively using the MMC.

18100

MM_NUM_CUTTING_EDGES_IN_TOA is used to set the maximum number of D or offset data blocks (max. 600).

The following machine data affect the way tools and cutting edges (D numbers) work in the NCK:

20270: CUTTING_EDGE_DEFAULT

20130: CUTTING_EDGE_RESET_VALUE

20120: TOOL_RESET_VALUE

20121: TOOL_PRESEL_RESET_VALUE

22550: TOOL_CHANGE_MODE

22560: TOOL_CHANGE_M_CODE

20110: RESET_MODE_MASK

20112: START_MODE_MASK

20090 = 2 ;

Spindle no. 2 is master spindle

20110, bit 3 can be used to define that the active tool and the tool offset are transferred as follows:

_ Bit 3=1 from the last test program to finish in test mode, or

_ Bit 3=0 from the last program to finish before activation of the program test

Prerequisite Bits 0 and 6 of MD 20110 must be enabled.

18082 MM_NUM_TOOL ：NCK（SRAM）所能处理的刀的数量。

18088 MM_NUM_TOOL_CARRIER ： 刀柄（toolholders）数量

18094 MM_NUM_CC_TDA_PARAM Number of TOA data FBW, S7

18096 MM_NUM_CC_TOA_PARAM Number of TOA data which can be set up pertool and evaluated by the CC

18100 MM_NUM_CUTTING_EDGES_IN_TOA Tool offsets per TOA module S7

18102 MM_TYPE_OF_CUTTING_EDGE Activate flat D number management (_ SW 4)

18105 MM_MAX_CUTTING_EDGE_NO Address extension interpreted as spindle number

18106 MM_MAX_CUTTING_EDGE_PERTOOL Maximum number of cutting edges per tool

18108 MM_NUM_SUMCORR Number of all sum offsets in NCK

18110 MM_MAX_SUMCORR_PER_CUTTEDGE Maximum number of sum offsets per cutting

edge (SW 5 and higher)

7.2 Machine data

18112 MM_KIND_OF_SUMCORR Properties of sum offsets in the NCK

18114 MM_ENABLE_TOOL_ORIENT Assign orientation to cutting edgesChannel-specific ($MC_ ... )

20096 T_M_ADDRESS_EXT_IS_SPINO Spindle number as address extension

20110 RESET_MODE_MASK Definition of control basic setting after power-up and RESET parts program endK2

20120 TOOL_RESET_VALUE Definition of tool for which tool length compensationis selected during power-up or onreset or parts program end as a function of MD

20110

20121 TOOL_PRESEL_RESET_VALUE Definition of the preselected tool for which thetool length compensation is selected duringpower-up and on reset or parts program endas a function of MD 20110

20126 TOOL_CARRIER_RESET_VALUE Active toolholder on RESET

20130 CUTTING_EDGE_RESET_VALUE Definition of tool cutting edge for which toollength compensation is selected during power-up or on reset or parts program end as afunction of MD 20110

20132 SUMCORR_RESET_VALUE Number for selecting sum offset

20140 TRAFO_RESET_VALUE Definition of transformation block which is selectedduring power-up and or RESET or partsprogram end as a function of MD 20110

20180 TOCARR_ROT_ANGLE_INCR[i] Minimum incremental step for orientational

toolholder (SW 5.3 and higher)

20182 TOCARR_ROT_ANGLE_OFFSET[i] Offset of the axis of rotation for orientational

toolholder (SW 5.3 and higher)

20184 TOCARR_BASE_FRAME_NUMBER Base frame of the table offset for orientational

toolholder with rotary table (SW 5.3 and higher)

20202 WAB_MAXNUM_DUMMY_BLOCKS Maximum number of blocks with no traversing

motions with SAR

20204 WAB_CLEARANCE_TOLERANCE

20210 CUTCOM_CORNER_LIMIT Max. angle for intersection calculation with tool

radius compensation

20220 CUTCOM_MAX_DISC Maximum value for DISC

20230 CUTCOM_CURVE_INSERT_LIMIT Minimum value for intersection calculation with

tool radius compensation

20240 CUTCOM_MAXNUM_CHECK_BLOCKS Blocks for predictive contour calculation with

tool radius compensation

20250 CUTCOM_MAXNUM_DUMMY_BLOCKS Max. no. of dummy blocks with no traversing

movements

20252 CUTCOM_MAXNUM_SUPPR_BLOCKS Maximum number of blocks with offset suppression

(from SW 4)

20256 CUTCOM_INTERS_POLY_ENABLE Intersection process possible for polynomials

(from SW 4)

20270 CUTTING_EDGE_DEFAULT Selected cutting edge after tool change

20272 SUMCORR_DEFAULT Number for activating a new cutting edge offset (SW 5 and higher) Tool Offset (W1) 10.00 7.3 Setting data Siemens AG, 2002. All rights reserved SINUMERIK 840D/840Di/810D Des cription of Functions Basic Machine (FB1) – 11.02 Edition Number Reference Name Identifier

20360 TOOL_PARAMETER_DEF_MASK Defines the effect of tool parameters

20390 TOOL_TEMP_COMP_ON Activation of temperature compensation for tool length (SW 6.1 and higher)

20392 TOOL_TEMP_COMP_LIMIT Maximum temperature compensation for tool

length (SW 6.1 and higher)

20610 ADD_MOVE_ACCEL_RESERVE Acceleration reserve for overlaid movements K1

21080 CUTCOM_PARALLEL_ORI_LIMIT Limit angle between path tangent and tool orientationwith 3D tool radius compensation

W5

22530 TOCARR_CHANGE_M_CODE M code for change of toolholder

22550 TOOL_CHANGE_MODE New tool offsets with M function

22560 TOOL_CHANGE_M_CODE M function for tool change